Samsung Galaxy J1(SM-j100h) Flash File Firmware latest version free for download here. You can download the latest version Samsung Galaxy J1 Flash File By click on the given download link. We also share some other models of J1 Like J100a, J100g and J100h you can also download all model flash files from the given download link. The Download link is free and the file is 110% tasted by the experts. You don`t have to panic just download and install the latest version on your Phone using any Flashing Software of Samsung.
The Samsung Galaxy J1 is powered by 1.2GHz dual-core processor and it comes with 512MB of RAM. The phone packs 4GB of internal storage that can be expanded up to 128GB via a microSD card. As far as the cameras are concerned, the Samsung Galaxy J1 packs a 5-megapixel primary camera on the rear and a 2-megapixel front shooter for selfies.
You can easily Use Odin Flasher to Install the custom Roms on Samsung Phones and also Z3x Box to flash or reset the Samsung phones. If you are using the Z3x Box Setup so Just follow the on-screen Tips to fully flash your phone. The Samsung Galaxy j1 is one of the best Android smartphone used by thousands of peoples around the world. To flash the phone the method is simple and easy but sometimes it is possible that your phone will be dead due to installing old or corrupted file on it. So before flashing just check the flash file version and after it just install the file on your phone.
How To Flash Samsung Galaxy J1: 1: Download file form official Rapid Gator Mirror or given the link on google drive. 2: After download zip file extract it: 3: Open Odin3v1.87 or the latest version of Odin or any professional flashing tool like Z3X BOX or NSPRO. 4: Then select one by all the files where you extract the zip file. 5: Then without clicking anywhere just on start or flash button and wait until done. 6: Important request does not flash if you are new in flashing. 7: If you want to do that the check you mobile battery charge up to 50%.
Device Name: Samsung Galaxy J1
File size: 570 Mb
Reginal Code: Pak:ind
SM-J100h→ click here SM-J100F→ click here SM-J100G→ click here
Samsung Galaxy J1 SM J100H Firmware Flash File 4.4.4 Stock Rom
www.androidduniya.com reminds readers it will not be held responsible for any damage to the device during or after installation of Samsung Galaxy J1 SM J100H Firmware using Odin. Bryn mawr post bac linkage. Readers are advised to proceed at their own risk because of hardware faults.
Initial Requirements to install Samsung Galaxy J1 SM J100H Firmware
Unzip the Odin .zip file and run/open the Odin3.exe file from the extracted files on your PC and install Samsung USB drivers.
Enable OEM to unlock (If applicable):
Firstly, Go to Settings » About phone » and tap “Build number” seven times to enable “Developer options”.
Secondly, Go back to the main Settings page, scroll to the bottom and select “Developer options” from there.
Thirdly, Under Developer options look for “Enable OEM unlock“ checkbox/toggle and make sure you Check it or turn it ON.
Samsung Sm-j100h/ds Flash File Download India
How to Install Samsung J100H 4.4.4 Firmware
Boot your Samsung Galaxy J1 SM J100H into Download mode
Firstly, Switch off your phone.
Secondly, Press and hold “Home + Power + Volume down” buttons for a few seconds until you see a warning screen.
Thirdly, Press Volume Up on the warning screen to accept it and boot into Download mode.
Once your device is in download mode, connect it to the PC with a USB cable. The Odin window on PC should detect the phone and show an “Added!!” message.
Now, extract the .zipped Samsung Galaxy J1 SM J100H Firmware file you have downloaded to get the Odin flashable.tar file inside. Skip this step if you already have a .tar file of the Samsung SM J100H Flash File.
Click on the AP tab on Odin window and select the .tar.md5 file from the Samsung Galaxy J1 SM J100H Firmware file that you have downloaded or can download it from the given below Link. Note:don’t play with any other options on the screen. Only you have to connect your Samsung Galaxy J1 device and select the PA tab.
Click the Start button on Odin and wait for it to finish the process. Once it has finished successfully, you’ll see a pass message on the Odin screen.
Finally, the device will automatically reboot after Odin complete the flashing. Now disconnect your Samsung Galaxy J1
Note: All product names, logos, and brands are the property of their respective owners. All company, product and service names used on this Blog are for identification and learning purposes only.
Also Read: Samsung Galaxy Beam gt-I8530 Android 4.1.2 Firmware Flash File Unable to activate windows store app store.